Best 1050 Ti Gpu Water Cooling

The Thermosphere cooling engine uses similar, yet refined as per needs of modern microprocessors, fin design as its ancestor. The cooling liquid accelerates through jet plate’s nozzle and turbulently continues its path through numerous very thin channels which provide extreme cooling surface area. EK-Thermosphere can also work flawlessly with reversed water flow which does not affect the cooling performance. Base is made of nickel plated electrolytic copper, backbone is made from laser cut brushed stainless steel plate while the top is made of quality cast acrylic material. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed in each exchangeable mounting plate and allow for safe, painless installation procedure. Block is mounted with enclosed M3x4 DIN7985 screws. G1/4″ threaded fittings can be used on both sides of the FC terminal. Up to four EK-Thermosphere water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block. GPU compatibility: EK-Thermosphere series waterblocks supports majority of modern nVidia and AMD high-end graphics cards via exchangeable mounting plates. The product however comes factory pre-fitted with mounting plate G80 (mounting pattern 58x58mm) and ready for use on modern nVidia GeForce GTX graphics cards only. Please check compatibility at EK’s CoolingConfigurator. To use this product on AMD and other nVidia graphics cards it is mandatory to purchase additional mounting plates: – G92: 53x53mm – R600: 54x54mm – GF560: 51x61mm – G200: 61x61mm Enclosed in the box: – EK-Thermosphere series water block /w pre-installed G80 mounting plate – mounting mechanism – thermal grease (TIM) EK-Ectotherm (1g)

Specifications:

Fan specifications:

Fan speed: 700-1500RPM

Air volume: 62CFM

Noise: 18.0-26.4dB (A)

Connector: 4Pin (2510)

Start-up voltage: DC 7V

Rated voltage: DC 12V

Rated current: 0.18A

Rated power: 2.16W

Size: 120X120X25mm/4.72X4.72X0.98″

Pump specifications:

Pump speed: 2000 RPM

Pump head: 1.2m H2O

Cold liquid flow rate: 96L/H

Noise: 25.0dB (A)

Connector: SATA

Rated voltage: DC 12V

Rated current: 0.25A

Rated power: 3W

Cold Head Size: 65×32.5mm/2.56×1.28″

Cold Plate size: 154x120x27mm/6.06×4.72×1.06″

Pipe length: 315mm/12.4″

Notes:

1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!

2. Please allow slight measuring deviation due to manual measurement.

Package included:

1 X GPU Cooling Fan

1 X Installation Kit

1 X User Manual

1. Block with 0.5mm micro channel injection design, all designed only for performance!
2. Block using large flow design, even if low raise pump can use it.
3. Block made by high purity copper, and electroplating to prevent oxidation and makes beautiful.
4. Inlet and outlet can change direction free.
Tips:
1. Please double check the graphics card detail model to ensure compatibility. Please feel free to contact us if you are not very sure.
2.2pcs G1/4 3/8″ ID 1/2″ OD Silver Compression Fittings are included, instead of the ones in the pictures.
3. Prohibit the use of alcohol containing coolant.
4. Graphics card block installation requires a certain skill and experience, because the graphics card manufacturing tolerances may have a certain impact on the block installation, we can assist buyers to solve such problems, but this can not be the basis of returns.
Compatibilities: EVGA RTX2080TI FTW3

100% new, fine workmanship, simple sense is very strong!
N-AS1050SI-X built for ASUS GTX1050 GTX1050TI Specifications of the graphics design ,please confirm before buying graphics specific specifications, to ensure the compatibility of water cooling block.
Water cooling block directly to the cooling core graphics (GPU), memory (RAM), as well as the graphics card power supply (VRM) these hot key parts of the graphics card, to ensure that the players and the stability of the overclocking, maintain a good temperature
Video card water head is designed using large flow, even if hm weaker pump can meet the demand
Water ccoling block at the bottom of the use of high purity copper manufacturing, and electroplating processing to prevent oxidation, more make water head of delicate and beautiful. Cover the use of high-quality POM material or imported acrylic materials, ensure the service life of water head and durability. Sealing material using a high standard of sealing ring resistance to ageing of fatigue, ensure the sealing water cooling block.
Video card water head is free to change direction, convenient players form a SLI system, can be in series or in parallel
parts list:
fast twist X 2
plugs X 2
thermal paste X 1
mounting screws X1
Compatible model:
RGB LED X 1
Compatible graphics card type:ASUS DUAL-GTX 1050-2G
Compatible graphics card type:ASUS DUAL-GTX 1050TI-4G
Compatible graphics card type:ASUS EX-GTX 1050-2G
NOTE: If you are unsure whether compatible, please contact the seller or view graphics brands and models, because the description have mentioned writing compatible graphics card name and model number .

The EK-Vector Strix RTX 2080 Ti RGB water block is specially designed for the ROG Strix version of NVIDIA® GeForce® RTX 2080 Ti graphics cards.

The water block covers the entire PCB length, and directly cools the GPU, VRAM and the VRM. The redesigned cooling engine has a larger footprint compared to the previous generation for better cooling performance

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used with reversed flow. 

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. Sealing is ensured by high-quality EPDM O-rings.

The block is equipped with 4 12V RGB LED strips which are compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

Both the NVIDIA® and ROG NVLink™ are compatible with this water block. 

ENCLOSED:

• EK-Vector Strix series high-performance water block
• Mounting mechanism with screw-in brass standoffs
• Necessary mounting screws, nuts, and washers
• 2x Nickel plated brass plug G1/4”
• 6mm Allen key
• Thermal pads
• Thermal grease EK-TIM Ectotherm (1g)

PLEASE NOTE:

ROG Strix RTX 2080Ti factory backplate is not compatible with this water block
Fittings are just for showcase and are not included
Should not be installed with any aluminum EKWB Fluid Gaming parts

Model: 3831109814123

The EK-Vector FTW3 RTX 2080 Ti RGB high-performance water block is specially designed for EVGA FTW version of NVIDIA® GeForce® RTX 2080 Ti graphics cards. The water block features a unique aesthetic cover over the block Terminal which is designed to showcase the graphics card model via LEDs, visible from the side.

The water block directly cools the GPU, VRAM and the VRM, and uses an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with pumps running at slower speeds. The jet plate and fin structure has been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed flow.

The base of the block is CNC machined out of nickel-plated copper while the top is CNC machined out of acrylic. Sealing is ensured by EPDM O-rings.

It features four integrated LED sources, two located in the terminal cover and one LED strip on each end of the water block which is compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

G1/4″” threaded fittings can be used on both sides of the terminal and for multiple GPU connectivity, please refer to our offer of Scalar GPU Terminals.

Both the NVIDIA® and EVGA NVLink™ are compatible with this water block.

Enclosed:

– EK-Vector FTW3 series high-performance water block
– Necessary mounting hardware
– 2x Nickel plated brass plug G1/4”
– 6mm Allen key
– Thermal pads
– Thermal grease

PLEASE NOTE:
EVGA FTW3® RTX 2080Ti factory backplate is not compatible with this water block. This product should NOT be installed with any aluminum Fluid Gaming parts!

Model: 3831109816783

Description:
This all-in-one liquid CPU cooler kit provides a 240mm heat sink, water pump, cylindrical water reservoir, dual fans, as well as installation accessories, which will dramatically improve heat dissipation experience, especially in terms of stability, silence, efficiency, and convenience. Liquid cooling simply works better than air cooling and the special design makes it easy for you to protect your valuable CPU.

Specifications:
1. 240mm black heat sink (with screw pack):
Appearance size: 27.5 * 11.8 * 3.2cm
Straight mouth height: 2cm
Diameter of straight tube: about 9.5 mm
Number of waterways: 18
2. LED fan:
Appearance size: 12 * 12cm
Power supply interface: large 4Pin + small 3Pin
3. Universal CPU block (with 4 pcs screws):
Description: Universal for INTEL / AMD Dual Platform (For INTEL 775,1150,1155,1156,1366,) (For AMD: AM2, AM3, AM3 +)
Note: Do not support for AMD4CPU CPU block, bracket supports for AMD INTEL mainstream hole installation.
Screw size: G1 / 4
Outside diameter: 12.9MM
Bottom contact size: 5 * 5cm, thickness 3mm
Material: Bottom: copper; Cover: transparent plexiglass

Pacakage List:
1 x 240mm Heat Sink within Screw Pack
2 x LED Fan
1 x Universal CPU Block within 4 Screws
1 x Universal GPU Block within 4 Screws
1 x Cylindrical Water Reservoir (Including 1 * screw pack, 2 * plastic bracket, 2 * metal bracket)
1 x Transparent Hose
1 x Water Pump with Shock Pad
1 x A Set of Water Pipe Connectors & Hose Clamps & Plugs

Description:
2 holes on the side of the cover, the water flows from the side.
0.8 mm copper columns on the copper base.
The water contact area becomes large, so the block can carry more heat from GPU quickly.
The surface flatness is less than 0.01 mm.The base can fit the GPU better, so that it can absorb more heat.The copper base is processed with anti-oxidization technology.
Installation Accessories: Get a 4 mounting screws.
Support 43*43 48*48 53*53 three hole spacing.
Suitable for graphics cards below 1050.

Powered by GeForce GTX 1050 Ti and integrated with 4GB GDDR5 128bit memory. Featuring windforce 2X with blade fan design

Conclusion

By our suggestions above, we hope that you can found 1050 ti gpu water cooling for you.Please don’t forget to share your experience by comment in this post. Thank you!