rinstips 
Nowadays, there are so many products of incubator heating cooling in the market and you are wondering to choose a best one. You have searched for incubator heating cooling in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings incubator heating cooling which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Lab Incubator, Cooling and Heating 2-60C, 12V/110V, 60W, 25L/0.88 cu. ft. Capacity
- Can heat samples to 60°C, cool down to 2°C. Current chamber temperature is displayed on the LED digital display.
- 25 Liter Capacity, accepts bottles and flasks up to 2L
- Temperature set in increments of 1C on the LED digital display
- If kept on the same shelf, temperature fluctuations of 0.5°C
- 110V Standard power cord included, as well as a 12V car adapter allowing it to run on the go
This incubator functions as both a cooler and a warmer by means of a thermoelectric (Peltier) system. It works without a compressor and is therefore 100% CFC/HDFC free. Despite its small size, its interior volume is 25L and can accept bottles and flasks up to 2L. Two removable shelves create 3 platforms. The desired temperature is set on the digital LED display, and the incubator immediately starts heating or cooling, while accurately monitoring the temperature inside and displaying it on the LED panel.
HEATING
The incubator can heat samples up to 60°C while using only 55W at 110V. A temperature gradient is present inside the chamber: the temperature at the top shelf is the set temperature; the middle shelf is 2°C below that; the bottom is 3°C below that (see graph). Within each shelf, the temperature only fluctuates by 0.5°C.
COOLING
The incubator is able to cool down to 2°C, using only 60W at 110V. Depending on the room temperature and humidity, it may not cool down all the way to 2°C. Again, a temperature gradient is present: the top shelf reaches the preset temperature (lowest is 2°C); the middle shelf is 1°C below that; the bottom shelf is 1°C below that. Within each shelf, the temperature fluctuates by only 0.5°C
SMALL FOOTPRINT
With a small footprint of 15 in x 13 in x 18.5 in, this incubator will not take valuable space while having a roomy 25L (9×14.5×10.5 in) chamber volume.
PORTABLE
At only 16 lbs and with a built-in handle, the incubator is easy to move around. A 12V DC car power cord allows the unit to heat or cool your samples on the go.
Inkbird ITC-308 Max.1200W Heater, Cool Device Temperature Controller, Carboy, Homebrew, Fermenter, Greenhouse Terrarium Temp. Control
- [Convenient Design] Plug and play design, easy to use. Support °C/°F display.
- [Dual Relay Output] Be able to connect with refrigeration and heating equipment at the same time.
- [Dual Display Window] Be able to display measured temperature and set temperature at the same time.
- [Buzzer Alarm] High and low temperature alarms are available when the temperature is over or the sensor is with issue.
- [Warranty & Safe] Warranty: 1 year. Maximum output load: 1100W(110V). It is with temperature calibration and compressor delay which can protect your refrigeration.
Specification:
Temperature Control Range: -50~99°C / -58~210°F
Temperature Resolution: 0.1°C / 0.1°F Temperature Accuracy: ±1°C (-50~70°C) / ±1°F (-50~160°F)
Temperature Control Mode :On/Off Control, Heating and Cooling
Input Power: 100 ~240VAC, 50Hz/60Hz
Temperature Control Output: Max. 10A, 100V~240V AC
Buzzer Alarm: High and Low Temperature Alarm
Sensor Type: NTC sensor (Including)
Sensor Length: 2m / 6.56ft
Input Power Cable Length: 1.5m (5ft)
Output Power Cable Length: 30cm (1ft)
Body Dimension: 140x68x33mm (5.5×2.7×1.3inch)
Socket Dimension: 85x42x24mm (3.3×1.7x1inch)
Ambient Temperature: -30~75°C / -22~167°F
Storage Temperature: -20~60°C / -4~140°F
Humidity: 20~85% (No Condensate)
Warranty: 1 Year
Package Included:
1x ITC-308 Temperature Controller
1x Manual
KETOTEK Digital Temperature ControllerAC 110 220V 10A Thermostat Regulator -50~110C Heating Cooling Control Incubator Relay
Inkbird Pre-Wired Digital Dual Stage Temperature Controller Outlet Thermostats 110V 1000W With 12" Stainless Probe Sensor DC Cord for Fermentation Kegerator ect
- 12inch Stainless Probe with 6.5ft DC cord
- Temperature calibration
- Dual relay output, be able to connect with refrigeration and heating equipment at the same time
- Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.
- Support reading with Centigrade or Fahrenheit unit
Features:
This temperature probe can be submersed into beer direclty during fermentation.
No need to worry about inserting a smaller probe into a separate thermowell temperature probe.
It’s compatible with INKBIRD’s following controllers:ITC-308,ITC-306T,ITC-310T.
Plug and play design,easy to use;
Dual relay output,be able to connect with refrigeration and heating equipment at the same time;
Support reading with Centigrade or Fahrenheit unit;
Maximum output load:1100W(110V);
Dual display window,be able to display measured temperature and set temperature at the same time;
Compressor delay protection for refrigeration control
High and low temperature alarms are available;
Specification
Temperature Control Range:-50~99°C/-58~210 °F
Temperature Resolution:0.1°C/0.1°F
Temperature Accuracy:±1°C(-50~70°C)/±1°F(-50~160°F)
Temperature Control Mode:On/Off Control,Heating and Cooling
Input Power:100~240VAC,50Hz/60Hz
Temperature Control Output:Max.10A,100V ~240VAC
Dimension Body:140x68x33mm(5.5×2.7×1.3inch)
Socket:85x42x24mm(3.3×1.7x1inch)
Input Power Cable Length:1.5m(5ft)
Output Power Cable Length:30cm(1ft)
Buzzer Alarm: High and Low Temperature Alarm
Over-temperature and sensor fault alarm
Ambient Temperature:-30~75°C/-22~167°F
Storage Temperature:-20~60°C
Measuring temperature range:-50℃~120℃
Sensor Type: NTC
Probe Material:Stainless steel
Probe Dimensions:6mmx300mm(0.24in x 12in)
Cord Length (excluding probe):2m (6.5ft)
Package Content:
1xITC308S temperature controller;
1xStainless Steel Probe DC Sensor
1xManual
Conclusion
By our suggestions above, we hope that you can found incubator heating cooling for you.Please don’t forget to share your experience by comment in this post. Thank you!
