The 10 Best Mercury Fuel Water Separator Filter Kit

The Moeller 033320-10 10 Micron Water Separating Filter Kit is designed for Mercury, Johnson, Evinrude, Yamaha, Suzuki, Honda, Tohatsu and Nissan engines, along with universal applications. Includes a powder coated reusable filter head, filter, barbs and plugs. Not recommended for use with electric fuel pumps.

Sierra fuel water separators remove over 99.8% of emulsified water from your gasoline. Sierra’s 10 micron filters are over 90% efficient at removing particles as small as 10 microns. All filters flow @ 90 GPH to feed even the hungriest motor. Sierra 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems.

Sierra fuel water separators remove over 99.8% of emulsified water from your gasoline. Sierra’s 10 micron filters are over 90% efficient at removing particles as small as 10 microns. All filters flow @ 90 GPH to feed even the hungriest motor. Sierra 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems. Contains: 1 – 18-7944 and 1 – 18-7853-1 Replaces: Mercury – 35-802893A4, Q4, 35-60494A4

Features: -Composite fuel filter clear bowl kit. -Water separating canisters. -High performance 3/8 NPT ports offer lower pressure drop rates. -Designed to trap the smallest particles and emulsified water from gasoline. Product Type: -Tools. Use: -Filter. Generic Dimensions: -10.25″ H x 14″ W x 19″ D, 24 lbs. Dimensions: Overall Height – Top to Bottom: -10.25 Inches. Overall Width – Side to Side: -14 Inches. Overall Depth – Front to Back: -19 Inches. Overall Product Weight: -24 Pounds.

Replaces Mercury 35-60494-1.
Replaces Racor S3213, B32013,18-7932-1,18-7932,18-7928-1,18-7928.
Filter Replaces Mercury Marine 35-809097,Racor S3213,Yamaha MAR-24563-03-00,18-7919,18-7919-1.

To replace element:
1.Drain the unit by loosen the drain screw.
2.Loosen and remove the filter element.
3.Loosen and remove the bowl from filter element.Please note the bowl is reusable,do not dispose unless broken.
4.Wipe O-ring gland clean,and coat bowl’s seal O-ring with fresh oil or grease and place it back to the gland.Then tighten the bowl onto filter element firmly by tool.
5.Coat filter element’s seal O-ring with fresh oil or grease and attach filter element onto filter head,and the tighten securely by tool.
6.Run engine and check for fuel leakage.

Attention:
1.Make sure you remove both the filter and the filter bowl from the mounting housing and put a light film of fuel on the o-ring.As delivered it will leak without the lubrication to allow for the proper crush.
2.For diesel transfer tank to filter the fuel before it enters the main tank.Only thing is you have to make sure to get the proper sealant for the threads. For The First time installation,in order to avoid any leaking at the threads.You’d better get some thread paste since the tape might plug the injectors if it were to come loosen.
3.Check and replace regularly.

Instructions:
To Drain Water:
1.Loosen drain screw to drain bowl of water.
2.Tighten drain screw.
3.Run engine and check for fuel leakage.

Safety Warning:
Periodically check fittings and filter element for leaks.Be careful when changed fuel filter element.Diesel is extremely flammable and highly explosive under certain conditions.Avoid spilling diesel.Always stop engine and do not smoke or allow open flames in the area while changing filter element.

This is a spin-on filter and water separator kit. It is designed for high performance applications, and with flow rate for 20 liters/min. It is simple to install and has a 60 PSI pressure rate. This kit comes with a reusable, corrosion-resistant head and three plus. Keep your marine motor running efficiently with this fuel filter water separator. Your engine will perform better than ever with clean. This fuel filter/water separator kit comes with reusable, corrosion-resistant filter head, water separating fuel filter, and 3 plus. Universal filter and mounting bracket included. For all 2 and 4 cycle engines. Flow rate 20 liters/min. Pressure rate: 60 PSI. Filtration capability: 10 micron. Replaces and are Interchangeable with Mercury #35-60494-1 & #35-807172. Thread type: 11/16″ Item# PM153104.

Water separating canister element with o-ring and the water sensor unit. For all 1996 and newer Mercury and Mariner V-6 EFI outboards. Note that the sensor plus is blue plastic. Check your owner’s manual for inspection and replacement schedules. The Quicksilver brand is the leader in delivering uncompromising engine oils, parts and accessories to the marine industry for over 65 years.  Quicksilver is the premier supplier of Mercury Marine Original Equipment replacement engine parts, oils, and accessories, but also works to serve all Original Equipment brands in the marine and powersports industries.  It has earned a loyal following by providing the highest quality products that are tested through some of the most rigorous environments and testing procedures. No aftermarket company comes close to the level of research and design as Quicksilver; buying Quicksilver is buying performance, protection and peace of mind.

To Drain Water: 1. Loosen self-venting drain plug to drain water from bowl into a container., 2. Tighten drain., 3. Use primer bulb to fill filter with fuel., 4. Start engine and check ensure there are no leaks. Thread Type / Size: Mercury Thread 11/16″ 16 T.P.I

When you’re out on the water having fun, you shouldn’t need to give your fuel system a second thought. With Moeller, you don’t. Our products are safe, reliable, and durable. For more than 25 years, Moeller Marine has been the industry standard in fuel system design and construction. Moeller’s reputation is built on innovative engineering, quality construction, and award-winning service.

If you have difficulty in installing, you can go to YouTube to find the appropriate installation video:https://www.youtube.com/watch?v=LyeqTDVzY-A.

Specification:
1.Fuel Water Separating Filter fit 3/8 Inch NPT Outboard Motors as well.
2.Maximum Flow Rate 30 GPH (57 LPH).
3.Port / Connecting Size M18 X 1.5 Center Thread.
4.These are more suited to compact off road diesel equipment:tractors,skid steers loaders,movers.
5.Filter Rating 10 Micron.10 micron filters are over 90% efficient at removing particles as small as 10 microns. 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems, Designed to trap the smallest particles and emulsified water from Diesel.

Product details:
1.Don’t be caught in the water without one of these Diesel spin-on filters.
2.Filters are designed for high performance applications, and with flow rate of 30 GPH on the R12T model, your engine will perform better than ever with clean, water-free Fuel.
3.The inlet and out let can be feed in on the same side or in one side out the other side.
4.Check and replace regularly.

R12T water separator and filter complete combo installation instruction:
1.Nylon collection bowl down when installed the water separator and filter.
2.This filter has four ports, two inputs and two outputs. We provide two plugs for the extra two ports. If you need to use two plugs, you must install them to the filter and tighten them.
3.Before installing the filter, you have to remove those plugs, teflon-tape them, and re-install them.Prevent leaks from these plugs.
4.All of the above steps are very simple to operate, you can manually disassemble, and then use the tool to install tighten.

Conclusion

By our suggestions above, we hope that you can found mercury fuel water separator filter kit for you.Please don’t forget to share your experience by comment in this post. Thank you!