rinstips 
Nowadays, there are so many products of roof and gutter heating system in the market and you are wondering to choose a best one. You have searched for roof and gutter heating system in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings roof and gutter heating system which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Prime Wire & Cable RHC1000W200 ROOF & GUTTER DE-ICING KIT ROOF HEATING CABLE
- 200 ft. Black roof & gutter de-icing kit, 1000 watts, 2 ft. 18/3 SJTW blue power cord
- Promotes water flow in gutters and downspouts
- Helps prevent water damage caused by ice dams
- Includes roof cable, shingle clips, spacers, owner’s manual & labeling for breaker & on/off switch
Roof and gutter De-Icing cables help prevent costly damage from ice Dam formation by preventing freezing of un-insulated roof eaves, Valleys, gutters and downspouts, and allows water to drain freely. This product is for use on inclined, tab-shingle roofs and in downspouts and gutters only. To ensure water can flow to the ground, cable should be installed on Unheated portions of the roof (usually the overhang) as well as in Valleys, gutter and downspouts. Roof and gutter De-Icing kits are available in lengths from 30 ft to 240 ft. These products are found as De-Icing and snow melting sets primarily in northern markets beginning in early October.
HEATIT HIRD 200 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable
- Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time.
- Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included.
- Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts.
- Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available
- Suitable for most roof and gutter configurations.
- Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable.
Similar items with 4 stars and above
HEATIT JHSF1 Self Regulating ROOF & Gutter DE-Icing Pre-Assembled Heating Cable 50-feet 120V
- HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional.
- Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material.
- ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug.
- Roof deicing application: Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic roofs, composite (tar and gravel) roofs and so on. Rated 10W/ft at 32°F (0°C) for roof deicing. For roof deicing application, you may need to buy clips and hangers separately.
- Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes. Two year limited warranty – If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
Similar items with 4 stars and above
Heat it HIRD 20 feet Roof Gutter De-Icing Cable
- Designed to prevent ice buildup, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts. When properly installed and operated, this product creates a path for melted snow or ice (“melt water”) to drain from the roof to the ground.
- Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available
- Suitable for most roof and gutter configurations. HIRD cable cannot be used on slate, stone, metal and ceramic roofs.
- Test the cable before installation. Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately few minutes, it should feel slightly warm to the touch. Then unplug the cable.
- Both CSA and ETL approved. 6 ft 18/3 cold lead with plug
- 5 watts/ft. Pre-assembled, ready to install, no maintenance required
- Easy instruction manual, clips and spacers are included.
- Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time.
What is the purpose of the heating cable?
The roof de-icing cable is designed to prevent ice buildup, known as ice dams, from forming on roofs and in gutters and downspouts. When properly installed and operated, this product creates a path for melted snow of ice (“melt water”) to drain from the roof to the ground.
Why you need to choose HIRD roof heating cable to protect your roof in the winter ?
HIRD roof heating cable was approved by both CSA and ETL. You can have more confidence on the product safety. Pre-assemble heating cable make installation easy for do-it-yourselfers with the included clips and spacers.
HIRD owned the aluminum foil and the tinned copper braid to make sure the 100% screen rate to make the product more healthy and more stable.
In the connection, HIRD take the industrial grade heat shrinkage tube technology to make the cable more durable.
How about the manufacturer?
The factory meet ISO9001 standard (audit by BV)in the production process and the company take a very strict requirement on the incoming material, production process control, finish good inspection etc. Advanced product structure engineering design, good raw material, strict production process, strict internal management plus many years maneuvering experience make HIRD more reliable.
This kit is only designed for use on:
Metal or plastic gutters/downspouts
Inclined roofs
Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes
Do not use this kit on any other type of roof, gutter and downspout, including: Roofs with wooden shingles, Rubber or rubber membrane roofs, Composite (tar and gravel) roofs, Wooden gutters or downspouts, Flat roofs
HIRD cable cannot be used on slate, stone, metal and ceramic roofs.
These types of roofs require special installation or the use of a self-regulating cable.
RHS Snow Melting System, roof and valley snow melting mats, Sizes 5′ feet x 13" inches, Color black, UL components, 5 ft. mat melts 2" inches of snow per hour, buy factory direct, (5′ ft. x 13" in.)
- RHS Valley Heater roof snow and ice elimination systems are good looking and cost effective. They ensure that the house owner will not have the frustration, property damage, and costs associated with water damage caused by the inability of roofs to drain water during winter months.
- Melts 2 inches of snow per hour, UL listed components are made to sustain the most harsh environments. RHS Valley heaters have a complete waterproof system which serves for the most demanding environments including hazardous and non-hazardous areas, as well as areas where corrosives may be of concern. The valley heaters provides 40 watts per foot at 120 volt.
- Easy installation, valley heaters are 5 feet length (can be made in 8′, 10′, 15′, and any other size up to 50′ ft. for custom orders) roofing grommet screws included with the system are 100% waterproof and easy to insert on the valley heaters.
- No more climbing on a ladder to shovel your roof, RHS Valley Heaters go right over the problem areas on the valley, 6.5″ inches to one side and 6.5″ inches to the other side to completely melt the snow from the valley, just attach the grommet screws at the labeled locations to secure in place and relax, and watch RHS Valley Heaters get the job done.
- RHS Valley Heater System provides with the most proficient, highly scalable and eco-friendly snow melting solution. Our roof systems are offered for all types of applications, including new construction, remodeling, and existing roofs. Installing RHS Valley Heater Systems can increase the life of your roof in addition it will enhance the value of your home or commercial property.
What is an Ice dam? An ice dam is a blockage of ice that forms at the edge of a roof and prevents melting snow (water) from draining off the roof. The water that backs up behind the dam can leak into a home and cause damage to walls, ceilings, insulation, and other areas.
Preventing Ice Dams
RHS Valley Heater System is one of the best purchases homeowners, contractors, field workers could take against snow accumulation on the roof. Our system will completely clear the most problem areas (valleys) from snow and ice from your roof, without any hassle of using a roofing rake or even using hazardous chemicals like sodium chloride and rock salt that will damage your roof. Lower cost on electric bill compared to other systems, our highly efficient system only draws the right amount of energy to melt ice and snow off your roof, saving on your energy bill. Expand the life of your roof and reduce the risks of falls, injuries and other related ice and snow dangers by installing the best roof deicing system by RHS
Similar items with 4 stars and above
Easy Heat ADKS-800 160′ Roof/Gutter Kit
- Eliminate damage caused by ice dams.
- The ADKS kit includes a de-icing cable with a 6 foot long cold section and plug, roof clips, and cable spacers.
- Complete with Clips and Spacers
- Approved For Metal and Plastic Gutters
- Prevents Water and Ice Damage by Providing a Clear Path for Melting Water
EasyHeat ADKS Series Kit of Roof and Gutter De-Icing Heat Trace Cable – 160 Feet Long – 800 Watt – Residential Grade – 120 Volt – 5 Watts per Foot with 6 Foot Power Cord and Plug and Roof Clips and Cable Spacers (Includes 5 CSK-12)
Prime Wire & Cable RHC600W120 ROOF & GUTTER DE-ICING KIT ROOF HEATING CABLE
- 120 ft. Black roof & gutter de-icing kit, 600 watts, 2 ft. 18/3 SJTW blue power cord
- Promotes water flow in gutters and downspouts
- Helps prevent water damage caused by ice dams
- Includes roof cable, shingle clips, spacers, owner’s manual & labeling for breaker & on/off switch
Roof and gutter De-Icing cables help prevent costly damage from ice Dam formation by preventing freezing of un-insulated roof eaves, Valleys, gutters and downspouts, and allows water to drain freely. This product is for use on inclined, tab-shingle roofs and in downspouts and gutters only. To ensure water can flow to the ground, cable should be installed on Unheated portions of the roof (usually the overhang) as well as in Valleys, gutter and downspouts. Roof and gutter De-Icing kits are available in lengths from 30 ft to 240 ft. These products are found as De-Icing and snow melting sets primarily in northern markets beginning in early October.
Thermal Resources Management Self-Regulating De-Icing Roof Heating Cable – for Heat Tracing and Ice Dam Prevention – Direct Plug-in System – 120 Volts (50 Feet + 6 Feet Cold Lead)
- HEAVY DUTY: The cable is designed for both commercial and residential applications. It has an inner insulation jacket and an exterior fluoropolymer jacket, providing more durability than most heat tracing cables.
- ENERGY EFFICIENT: The cable is self regulating meaning that the heat output is adjusted based on the surrounding temperature. The cable will decrease its heat output during warm weather, increasing energy savings. (8W Per Foot Wattage at 10C)
- PRE ASSEMBLED: Comes with a 6’ cold lead and light up plug for easy installation. Cables are designed to be crossed and overlapped without concern of short circuit or burnout.
- APPLICATIONS: Suitable for freeze protection, sprinkler tracing, roof and gutter de-icing, heat loss replacement and frost heave prevention. May be installed on shingled roofs, metal roofs, asphalt roofs, flat roofs and more.
- WARRANTY: Includes a manufacturer’s warranty of 2 years from the date of purchase. TRM is an industry leading, Canadian-owned, designer and manufacturer of premium heating cable and systems in the commercial, industrial and residential sectors.
TRM Heating Cable 120 Volts – 6 Feet Long with 6 Feet Cold Lead
The self-regulating heating cable is ideal for heat tracing in commercial or residential applications. TRM’s SR cable is suitable for applications such as freeze protection, sprinkler, roof and gutter de-icing, heat loss replacement, and frost heave prevention.
This cable is a cost-effective solution for most heat tracing applications, with a range of fastening products that can be designed to match your project’s specific requirements. The semi-conductor core regulates its heat output based on the surrounding temperature and can vary its heat output along the cable’s entire length, saving energy and eliminating hot spots along the pipe. This means that the cable uses less energy when it is warm outside, and more energy when it gets colder
Unlike cheap heat cables, TRM heating cables are designed to be crossed or overlapped to suit the specific site conditions.
Technical Specifications
- Cable Construction: Self regulating insulated core, woven tinned braid, with a polyolefin outer jacket.
- Cable Ending: The cable is preterminated with factory end seal and power connection point.
- Voltage: 120 Volts. (120 Volt units will come with a 6 feet cold lead and a lighted plug).
- Wattage Per Foot: 8 W Per foot at 10C. When cables are surrounded by ice and snow, the cables will generate 12W per linear foot.
Controls and GFI
The cable can function safely without the use of controls, and is designed to be simply plugged into a standard wall outlet. It is recommended to utilize thermostats or controllers to maximize the efficiency of the cables while simultaneously minimizing the electrical costs.
Similar items with 4 stars and above
Prime Wire & Cable RHC150W30 Roof & Gutter De-Icing Kit Roof Heating Cable
- 30 ft. Black roof & gutter de-icing kit, 150 watts, 2 ft. 18/3 SJTW blue power cord
- Promotes water flow in gutters and downspouts
- Helps prevent water damage caused by ice dams
- Includes roof cable, shingle clips, spacers, owner’s manual & labeling for breaker & on/off switch
- Total Outlet: 1
Roof and gutter De-Icing cables help prevent costly damage from ice Dam formation by preventing freezing of un-insulated roof eaves, Valleys, gutters and downspouts, and allows water to drain freely. This product is for use on inclined, tab-shingle roofs and in downspouts and gutters only. To ensure water can flow to the ground, cable should be installed on Unheated portions of the roof (usually the overhang) as well as in Valleys, gutter and downspouts. Roof and gutter De-Icing kits are available in lengths from 30 ft to 240 ft. These products are found as De-Icing and snow melting sets primarily in northern markets beginning in early October.
Grip Clip Asphalt Shingle Roof Clips for Installing Heat Tape, Prevent Ice Dam Damage to Roof and Gutters, Simple Nail Free Cable Clips (25 Pack) (Silver)
- Install heat cable to asphalt shingle roofs without creating holes or voiding roof makers warranty
- No tools needed and can be installed in cold weather
- Anodized raw aluminum clips install in 3 seconds and can be re-positioned
- Compatible with all manufacturers of ice dam prevention heat tape or heat cable wiring systems
- Grip Clips do not loosen and can hold over 25 pounds per clip for a secure long lasting solution
Grip Clip roofing cable clips come in a pack of 25 clips and provide a simple and effective solution to your roof cable installation needs. The nail free design does not require any additional tools due to its innovative “toothy pincher” design. The Grip Clip teeth grab the underside of the asphalt shingle producing a strong grip. No additional roofing tools are needed, making for a safer installation process. To re-position a Grip Clip, simply lift the edge of the shingle and slide the Grip Clip up to release the teeth. A common issue with ice dam cable installations is cable ends making contact and shorting out. Grip clips prevent this from happening by remaining secure and lasting indefinitely. Grip Clip is the only clip that allows for a building code compliant application of self-regulating heat cables near the center of the roof valley, where you want them. Using traditional clips requires that fasteners are driven through the valley flashing, which violates most building codes. Grip Clips can also be used on other roofing cable applications such as seasonal holiday string lights. Grip Clip is a Minnesota-based company with expert support staff available to help solve your roof ice dam problems.
Conclusion
By our suggestions above, we hope that you can found roof and gutter heating system for you.Please don’t forget to share your experience by comment in this post. Thank you!
